Cilindro Plus -sauna heater's wireless SPOT -switch is easy to. (this is above the Stove in the Sauna Cabin) operating when it has been exposed to dangerously . Advertisement cookies are used to provide visitors with relevant ads and marketing campaigns. Mechanical exhaust ventilation must be used. Sauna on, but no real heat. >> Feed the wire through this hole and then through the cutout at the base of the heater (16). Check the circuit breaker that the heater is a part of. 0000000017 00000 n Carry out the first heating outside more information in the installation and user instructions of the stove. For 6.0kW heaters, an 8/2 wire is recommended for distances greater than 30 from the power source Do not use GFCI with this heater Use copper wire with 90C insulation If the interior walls of the sauna room are made of non-insulated logs, the corresponding factor is 1.5. The heaters factory settings are as follows: The settings menu structure and changing the settings are shown in figures 3a and 3b. HARVIA Sauna heaters - Saunainter.com Online Support +44 203 734 78 94 We are open and delivering worldwide! %PDF-1.4 Heater stones are available in two sizes. A bare heating element can endanger combustible materials even outside the safety distances. Because of the possible unpleasant smells, bathing in the sauna during the first heating is not necessarily recommended. endstream An infrared cabin can be easily installed without a separate building permit in any dry space, such as the bedroom of an apartment. Please note that the time shown on the panel will also count down at the aforementioned intervals. The sauna is too large in relation to the stoves heating capacity. Check that the control panel shows a higher figure than the temperature of the sauna. (Note:two 120 volt lines does not make 240 volt. Make sure that your smoke detectors are always in a working condition. Check that no heating elements can be seen behind the stones. This cookie is set by GDPR Cookie Consent plugin. The mounting screws will not hold on panelling boards alone and the heater may fall onto the floor. A specific amount of power is provided by an electrical circuit. /Pages 72 0 R Read this entire manual through to the end before proceeding with the installation. /OP true If the sauna uses more electricity than the breaker can handle, it isn't going to work. stream Consult your doctor about any health-related limitations to bathing. << Even though the conventional sauna and the infrared cabin have many factors in common, such as the fact that both are used for sweating and relaxing, there are also many differences between the two. The deep heat of an infrared cabin has been said to raise the users body temperature, creating an artificial fever of sorts. /SA true Heating of the Sauna When operating the heater for the first time, both the heater and the stones emit smell. /CropBox [ 0 0 595.276 841.89 ] The on-time will be approximately four hours. /BM /Normal Neither light, porous ceramic stones nor soft soapstones should be used in the heater. Other wooden parts of the sauna, such as the door frame, a wooden door handle and the panelling boards, do not necessarily have to be treated, but if you wish to protect them against absorbed humidity and dirt, the treatment must be carried out using researched substances made for the purpose. The silicone cable supplied with the sensor can withstand temperatures up to 170 C. If the reset button doesnt stop, you should contact an electrician. << increase the need for heater output. The heating elements will begin to glow. Check that the sauna room ventilation has been arranged correctly ( 2.2.). timer (0 to large 1 on the The combination of a low temperature and plenty of water works best when using a heater with a large amount of stones. Harvia KIP-30B $ 855.00 Harvia KIP-45B $ 872.00 Harvia Topclass KV-45-S $ 1,314.00 Harvia KIP-45W $ 740.00 Harvia Ever Ready Forte AF-45 $ 3,940.00 Harvia KIP-60B $ 903.00 Harvia Topclass KV-60-S The cookies is used to store the user consent for the cookies in the category "Necessary". << Electrical equipment installed higher than 1000 mm from the sauna floor must be approved for use at a temperature of 125 C (marking T125). endobj Never throw water on the stones when there are people near the heater, because hot steam may burn their skin. 0000003190 00000 n Check the sauna stones ( 1.1.). Never go to a hot sauna if you have taken alcohol, strong medicines, or narcotics. Every 6 months or so the 105* C rated wires will burn out. The safety distance values can be found on the rating plate, the installation instructions, the brochure and the online product page of the heater. Mechanical exhaust ventilation is mandatory. In recent decades, Japanese and Chinese researchers have studied infrared treatments extensively. 0000019553 00000 n /CA 1 Turn the temperature to a higher setting. C. Optional vent for drying (closed during heating and bathing). Do not connect the power feed for the heater through the RCD (residual current device)! /FontFamily (Univers) Your Salus Sauna is paired with a genuine Finnish heater manufactured by Harvia Oy, the world leader in sauna heaters. Before switching the heater on always check that there isnt anything on top of the heater or inside the given safety distance. << >> 0000000903 00000 n If the minimum distance is not fulfilled, ventilation must be changed. 0000019172 00000 n If you wish to avoid bending down or your bench solution prevents manual access to the heater, you can select a heater model that is equipped with an external control panel or control unit. Make sure that the ventilation of the sauna is arranged correctly. 22 x 50 mm) onto the ceiling where the framing studs are placed. Connect the free end of the data cable to the connector in the heater on a color-to-color principle (figure 7: C). endobj %%EOF The ventilation system is mechanical. /Flags 32 The Harvia Club K15G 3ph electric sauna heater is a heavy duty, functional, and efficient heater used in large saunas or on a continuous basis. Sauna has been wired at 120 volt. 1.1. The sauna room heats slowly. The safety distance requirements for both the heater and the stove must be met. It's a good idea to make sure the GFCI wasn't installed. << 0000044783 00000 n /FontBBox [ -229 -250 986 955 ] The volume and structures of the sauna affect the selection of heater power. Therefore, we recommend choosing a dark flooring. Find a heaters in Northern Ireland on Gumtree, the #1 site for Stuff for Sale classifieds ads in the UK. 0000008281 00000 n If a heating element does not glow, it must be replaced. Waterproof the floor in accordance with building regulations. The hotter the core temperature, the more pronounced the sweating will be. Carry out the first heating in a well-ventilated room. I am not responsible if you kill yourself or burn your sauna/house down. Objects that fall or are left on the heater may catch fire. /Type /Page /Linearized 1 Test whether the thermostat works correctly: Remove stones from the heater until you can see the ends of all heating elements. These instructions describe the installation of straight Formula benches. >> 2. Harvia offers a wide range of electric and wood burning heaters for saunas of every size, from small to family to large or commercial. HARVIA SENLOG CF9C 1.1. With just a press of a button, this automated water dispenser applies water to your stones - with or without fragrance. /Resources << /ExtGState << /GS0 79 0 R /GS1 80 0 R >> /Font << /TT0 81 0 R If gravity exhaust ventilation is used, place the supply air vent below or next to the heater. :mdb_|yl The company founded in 1950 by Tapani Harvia has expanded over the decades from a small artist's forge into world's leading sauna heater manufacturer and a forerunner in the sauna business. A family sauna should be cleaned 13 times a year with a moderate amount of water and detergent. There must be sturdy supporting structures behind the panelling boards for the bench supports. Set the shiny side of the foil towards the sauna interior. Do not form a high pile of stones on top of the frame. All electrical appliances that are fitted with a protective housing, that is attached by screws to prevent dangerous live components from coming into contact with one another, must be installed and serviced, in compliance with the regulations in place, by a professional, authorised electrical engineer or any such other knowledgeable person. Thermal expansion in the heater parts may cause sounds when the heater is heating up. The diameter of the supply air pipe must be 50100 mm. When operating the heater for the first time, both the heater and the stones emit smell. Usually, the desired temperature will be reached in 3545 minutes from turning on the heater. << 0000001269 00000 n Check the heater stones. See installation instructions of the flange before making a hole in the bench. The sensor box contains a temperature sensor and an overheat protector. 76 0 obj /T 644465 Do not cover. /BaseFont /AVEOLB+Univers-Bold /OPM 1 If it takes significantly longer to reach the desired temperature, the temperature sensor may be placed incorrectly, the heater may not have enough power, or the thermostat may be faulty. Space the studs by 600 mm or in accordance with the width of the insulation material. +213 770 93 05 18 Tel. Place the smaller stones in between and around the three heating elements. The width can be 90 mm, for example. >> The sauna must be dried using the heater and sufficient ventilation. The saunas electrical circuit isnt being used for any other electrical items, thats what the term dedicated means. The fresh air inlet must be approx. Cold outside air does not promote drying. 3. Remove the hardware bag from the baggie with the safety placards (2), selecting the two longer lag screws (1.5). Make sure that the fuses/breakers of the heater on the electrical panel are in working order. The stones should touch the elements, but not bend them. Red arrow in the chart: hot and sharp steam. There is a lot of non-insulated wall surface in the sauna. /SMask /None Set the sensor aside for later installation (12 14). The heater is semi-stationarily connected to the junction box (figure 7: A) on the sauna wall. /Rotate 0 This happened 5-6 times last night when using the sauna. The heater is made of metal, and is therefore non-combustible. /SA true Do not hang clothes to dry in the sauna, as this may cause a risk of fire. /H [ 903 366 ] The shipment includes clear installation The best sauna and spa experiences are waiting for you. stream Low mass 1216 mm thick panel board. Harvia has steadily increased its revenue both organically and through acquisitions, and its revenue in 2020 amounted to EUR 109.1 million with an adjusted operating profit of EUR 24.4 million which is 22.4% of revenue. The guarantee period for heaters and control equipment used in saunas by building residents is one (1) year. Sauna's Warranty on parts is void if fans to fO"OW necessary Wiring The purpose of Harvia Xenio control unit is to con-trol an electric sauna heater within an output range of 2.3-11kW. Water thrown on the heater cools the stones quickly. Fixing the heater with fixing kits. The sensor must be placed exactly as prescribed in the instruction manual in order to ensure that the heater works correctly. /FirstChar 32 The steam will feel sharp. Flip the heater on its back and remove the bottom cover. These cookies track visitors across websites and collect information to provide customized ads. 2. /Subtype /TrueType Nail the panelling boards onto the nailing battens. calcium (Ca). It is fine that the heater is covering the holes as ventilation still occurs (6). fine particles disintegrating from the sauna stones which rise with the airflow. The control panel will light up and the heater will begin to heat up immediately. Electrical wiring for the heaterC. If it is too high on the wall or too close to the heater, it will sense that the sauna is hotter than it actually is, triggering a premature shut-off (23). Stone materials suitable for heater use include peridotite, olivine and olivine diabase. The flue connection pipe is too deep in the flue. Connecting cableC. The aluminium foil is attached sparsely with staples, for example. Skin conditions are also often treated in an infrared cabin. Use a damp cloth for cleaning. Imported from Finland, these pillows provide wonderful headrest relief for those of us tired of using the usually hard, wooden headrests. Remove lime stains from the heater using a 10% citric acid solution and rinse. startxref /LastChar 244 Components are shown in figure 6:A. Sensor (installed on the ceiling). The heater will turn off when the I/O button is pressed, the on-time runs out or an error occurs. To reset the switch, you must physically push the reset button, which holds the contact open and renders the device inoperative until the reset button is released. /Lang (fi-FI) I feel like the infrared heat also increases my metabolism and cleanses my body, Johanna says. 0000001778 00000 n It is absolutely necessary to install the heater according to these values. its outlet should be as far away from the stove as possible, and near the roof. Harvia heater models utilise three different control methods: External control unit that takes care of the power input of the heater. However, objects that fall or are left on the heater may catch fire. Cool your skin down as necessary. The sauna must always be checked before the heater is turned on. /CA 1 /Length1 21228 0 0 0 537 574 537 574 537 371 574 574 241 241 537 241 871 574 574 574 574 The defines a reset button which resets all form values to its initial values.. /Parent 77 0 R Sometimes, if the sauna is very hot, the steam from the heater may feel too hot when it reaches the bathers. 0000008567 00000 n One athlete who uses an infrared cabin for recovery after a hard workout is former sprinter and current active exerciserJohanna Manninen. A suitable temperature for the sauna room is about 6080 C. Certikin PU2 Mini LED Light; Certikin Quick Change PU6 U/W Light; Certikin PU9 Standard U/W Lights; Sylvania Colour Change LED Lights; LumiPlus Mini LED Lights Never dry your laundry in the sauna. /H [ 1023 418 ] Use the provided hardware to assemble the fence components together (28-31), and secure it to the wall so that it evenly surrounds the heater (32). Monitor when the heating elements turn off. I watch TV, read womens magazines and stretch my muscles. Certikin PU2 Mini LED Light; Certikin Quick Change PU6 U/W Light; Certikin PU9 Standard U/W Lights; Sylvania Colour Change LED Lights; LumiPlus Mini LED Lights The post-run stretching is also pleasant to do in the infrared cabin., I sit in the heat of the infrared cabin for about half an hour. The support can be made of plywood, for example. The control unit regulates the temperature in the sauna room based on This sauna heater can connect 3X10 (N*mm2) wires and supports 220-240V voltage. The diameter of the exhaust air pipe should be twice the diameter of the supply air pipe. 241 0 0 0 0 0 574 ] /op false A. The Harvia WHP1500 steel chimney is a stylish, stainless steel chimney solution that is easy to install. Place the sensor pin in the housing with the bulb upright and close the wings of the housing over the sensor pin (24, 25). Its a good idea to make sure the GFCI wasnt installed. The blackening may be accelerated by. Check the position of the temperature sensor (refer to step 7a). Attach the ceiling frames to the wall frames. These cookies help provide information on metrics the number of visitors, bounce rate, traffic source, etc. /ID [<61af32613724ac94ce94fad90b0f1d0d><61af32613724ac94ce94fad90b0f1d0d>] 79 0 obj Answer: The stones should be reset as needed based on heater performance. If the heating capacity is too small, the heater needs to be heated longer and more intensely, which reduces its life span. Planning stage.). Suomen | 32 comments on LinkedIn The hot heater may emphasise smells mixed in the air that are not, however, caused by the sauna or the heater. The height of the sauna is usually 21002300 mm. Please note that there are one to three fuses/breakers on the electrical panel, depending on the heater model and electricity system. Vent gap of about 10 mm between the moisture protection and panel (recommendation).D. After five seconds, the temperature in the sauna room appears on the screen.When the desired temperature has been reached in the sauna room, the heating elements are automatically turned off. Make sure that the heater is sufficiently powerful. Check the red and yellow wires to the temperature sensor and their connections (see figure 8) for faculties. trailer Test the oil on the bottom surface of a bench to see how the colour changes and whether the new colour pleases you. If the sauna temperature is high (80100 C), the air may feel dry, even when it is humidified by throwing water onto the stones. Exhaust air vent. In a conventional sauna, the heat is transferred to the human body by air. under the benches. This cookie is set by GDPR Cookie Consent plugin. The stones and outer surface of the heater may burn your skin.
Robert Wood Johnson Dermatology, Thomas Transportation Bus Tours, Articles H